Vertex Identifies Fully Developed Stope Block for Production
Released
Released
Announcement PDF
VVTXVVVVV
ASX:VTX
ASX ANNOUNCEMENT 28TH APRIL 2025
VTX IDENTIFIES FULLY DEVELOPED STOPE BLOCK FOR
PRODUCTION START-UP
HIGHLIGHTS:
•
VTX’s Technical Services team has identified a fully developed stope block to include in the mine production
start-up.
•
Stopes are suitable for airleg mining which will augment jumbo production.
•
Stope blocks contains an Inferred Resource of 2,075 tonnes at 17.8 g/t Au and forms part of the 2023 Mineral
Resource Estimate. With the lower block having over 700 tonnes at 42.5 g/t. The planned stope width is the
same as the interpretation of the mineralisation. (Refer to Table 1 in Appendices 1) (VTX ASX announcement 22/06/23)
•
Stopes are additional to the PFS mine schedule which is illustrated in Figure 2 showing the location of the
additional stope.
•
Stope blocks are fully developed and have been sampled from development.
•
This stope can be exploited as soon as services have been established.
Figure 1 – Arrangement of stope blocks
W. www.Vertexminerals.com
E. info@vertexminerals.com.au
VVTXVVVVV
Figure 2 – Location of additional stopes compared to PFS schedule
Vertex Minerals Limited (ASX:VTX, Company) is pleased to announce that the Company’s engineering and geology
team at the Reward Mine have identified an additional two stope block that have not been previously reported.
These stopes will be incorporated into the overall mine schedule, but provide an early source of mill feed.
The stopes were developed by a previous operator and are accessible from existing development. The additional
stope blocks contain an Inferred Resource of 2,075 tonnes at 17.8 g/t Au containing 1,189 ounces of gold with
the lower block having over 700 tonnes at 42.5 g/t. The planned stope width is the same as the interpretation of
the mineralisation. These stopes forms part of the Mineral Resource Estimate reported in VTX Announcement
22 June 2023. They were not included in the production forecast detailed in the 2024 Pre-Feasibility Study
(Announcement 3 January 2024). This was due to the complexity of existing airleg workings and uncertainty
around access and ground conditions, which established these areas into an Inferred Resource Category.
Note: ‘The Mineral Resources are additional to the Ore Reserves.’
Subsequent investigations have concluded that the stopes are fully developed and accessible. The quartz veins
are exposed in the existing development and have been sampled. The Company plans to exploit this stope once
the mine services have been established and bring this stope into the initial stages of the production schedule.
Vertex’s Executive Chairman, Roger Jackson commented: “Our new technical team has been established, and it is
great to see them looking for the opportunities to add value to the high grade underground production start-up.
This really does show the potential this mine has for high grade expansion. We are in the process of re-opening the
underground mine with the establishment of mine services. Dewatering of the declines has commenced and is
progressing to schedule.”
W. www.Vertexminerals.com
E. info@vertexminerals.com.au
VVTXVVVVV
This announcement has been approved by the Vertex Board of Directors
Further Information:
Roger Jackson, Executive Chairman
roger@vertexminerals.com.au
Tully Richards, Technical Director
tully@vertexminerals.com.au
Follow Vertex Minerals on LinkedIn
COMPETENT PERSONS STATEMENT
The information in this report that relates to Exploration Results and Exploration Targets is based on information compiled
by Mr. Roger Jackson, a Director and Shareholder of the Company, who is a 25+ year Fellow of the Australasian Institute of
Mining and Metallurgy (FAusIMM), Fellow of the Australian Institute of Geoscientists (FAIG) and a Member of Australian
Institute of Company Directors. Mr. Jackson has sufficient experience which is relevant to the style of mineralisation and
type of deposits under consideration and to the activity which he is undertaking to qualify as a Competent Person as defined
in the 2012 Edition of the “Australasian Code for Reporting of Exploration results, Mineral Resources and Ore Reserves”.
Mr. Jackson consents to the inclusion of the data contained in relevant resource reports used for this announcement as well
as the matters, form and context in which the relevant data appear.
FORWARD LOOKING STATEMENTS AND IMPORTANT NOTICE
This report contains forecasts, projections and forward-looking information. Although the Company believes that its
expectations, estimates and forecast outcomes are based on reasonable assumptions it can give no assurance that these
will be achieved. Expectations and estimates and projections and information provided by the Company are not a guarantee
of future performance and involve unknown risks and uncertainties, many of which are out of Vertex Minerals’ control.
Actual results and developments will almost certainly differ materially from those expressed or implied. Vertex Minerals
has not audited or investigated the accuracy or completeness of the information, statements and opinions contained in
this announcement. To the maximum extent permitted by applicable laws, Vertex Minerals makes no representation and
can give no assurance, guarantee or warranty, express or implied, as to, and takes no responsibility and assumes no liability
for the authenticity, validity, accuracy, suitability or completeness of, or any errors in or omission from, any information,
statement or opinion contained in this report and without prejudice, to the generality of the foregoing, the achievement
or accuracy of any forecasts, projections or other forward looking information contained or referred to in this report.
Investors should make and rely upon their own enquiries before deciding to acquire or deal in the Company’s securities.
JORC COMPLIANCE STATEMENTS
Where statements in this announcement refer to exploration results which previously been reported, the Company confirms
that it is not aware of any new information or data that materially affects the information included in the original
announcements, and in the case of estimates of Mineral Resources, that all material assumptions and technical parameters
underpinning the estimates in the relevant market announcements continue to apply and have not materially changed.
The Company confirms that the form and context in which the Competent Persons’ findings are presented have not
materially modified from the original market announcements.
W. www.Vertexminerals.com
E. info@vertexminerals.com.au
JORC Code, 2012 Edition – Table 1 report template
Section 1 Sampling Techniques and Data
(Criteria in this section apply to all succeeding sections.)
Criteria
Sampling
techniques
Drilling
techniques
JORC Code explanation
Commentary
• Nature and quality of sampling (eg cut channels, random chips, or
specific specialised industry standard measurement tools appropriate
to the minerals under investigation, such as down hole gamma
sondes, or handheld XRF instruments, etc). These examples should
not be taken as limiting the broad meaning of sampling.
• Include reference to measures taken to ensure sample representivity
and the appropriate calibration of any measurement tools or systems
used.
• Aspects of the determination of mineralisation that are Material to the
Public Report.
• In cases where ‘industry standard’ work has been done this would be
relatively simple (eg ‘reverse circulation drilling was used to obtain 1
m samples from which 3 kg was pulverised to produce a 30 g charge
for fire assay’). In other cases more explanation may be required,
such as where there is coarse gold that has inherent sampling
problems. Unusual commodities or mineralisation types (eg
submarine nodules) may warrant disclosure of detailed information.
• Diamond drilling – Variable sample length depending on vein
thickness. Quartz veining was half-cored by diamond saw except
where veining was isolated and narrow. Core cut down long axis with
same relative portion of sampled for each interval. Routinely a few
centimetres of wall rock around the vein(s) were included in the
sample to ensure that the vein footwall and hanging wall were left
intact. Sampling of wall rock carried out adjacent to high grade
intervals to test for peripheral mineralization with minimal values
returned.
• Reverse Circulation Drilling – Samples collected over 1m intervals via
a cyclone and split to 3kg samples for submission to the laboratory.
The only RC holes that intercepted the mineralised domains
interpreted in this estimate have diamond core tails through the
mineralised intervals.
• Face Sampling - Face samples were approximately 8kgs of
representative vein material taken by a geologist from the face. Only
quartz vein material was sampled, with two or more samples
collected if two or more veins are present. The distance between
faces is approximately 1.75m and generally every second face was
sampled giving approximately 3.5m sample spacing or rarely a 5.4m
sample spacing
• Diamond Drilling – Surface diamond drill holes were either NQ3 or
HQ3 in size whereas underground drill holes were LTK48. Core was
oriented using the Ballmark method.
• Drill type (eg core, reverse circulation, open-hole hammer, rotary air
blast, auger, Bangka, sonic, etc) and details (eg core diameter, triple
or standard tube, depth of diamond tails, face-sampling bit or other
type, whether core is oriented and if so, by what method, etc).
•
Reverse Circulation Drilling – RC holes were generally 130mm
diameter face sampling bits with diamond core tails through
mineralized zones.
Criteria
Drill sample
recovery
Logging
JORC Code explanation
Commentary
• Method of recording and assessing core and chip sample recoveries
and results assessed.
• Measures taken to maximise sample recovery and ensure
representative nature of the samples.
• Whether a relationship exists between sample recovery and grade
and whether sample bias may have occurred due to preferential
loss/gain of fine/coarse material.
• Whether core and chip samples have been geologically and
geotechnically logged to a level of detail to support appropriate
Mineral Resource estimation, mining studies and metallurgical
studies.
• Whether logging is qualitative or quantitative in nature. Core (or
costean, channel, etc) photography.
• The total length and percentage of the relevant intersections logged.
• Diamond Drilling - Core recovery (total core recovery) averaged
>99% and the average RQD was 75%.
• Reverse Circulation Drilling – Bag containing the 1m sample intervals
were weighed prior to sub-sampling. No RC intervals intercepted
mineralisation therefore recovery not an issue.
• There is no apparent relationship between sample recovery and
grade.
• Core was laid out in an angle iron with a base of hole line marked for
core orientation. All artificial core breaks were marked by red
chinagraph crosses. The core also had metre marks, tray and hole
numbers marked in chinagraph pencil prior to digital photography.
Geotechnical logging was completed with recovery, rock quality
designation (RQD), fracture frequency and orientation quality digitally
recorded in Excel spreadsheets. Core was logged for geological and
geotechnical parameters, with data collected digitally and transferred
directly to the database. Holes were logged in detail for alteration,
lithology, structure, vein style and mineralisation by geologists with
data being plotted and interpreted on section during drilling. High
quality digital photographs are available for all recent core.
• Reverse Circulation Drilling – RC holes logged for lithology, colour,
structure, alteration, mineralisation, weathering & oxidation, and vein
quartz characteristics. As field staff sampled each hole the following
information was recorded: Hole Name, Sample Name, Interval,
Sample date, sampler name(s), Sample Mass, and sample moisture.
This data was subsequently digitally recorded in Excel spreadsheets.
Subsampling
techniques
and sample
preparation
• If core, whether cut or sawn and whether quarter, half or all core
taken.
• If non-core, whether riffled, tube sampled, rotary split, etc and
whether sampled wet or dry.
• For all sample types, the nature, quality and appropriateness of the
sample preparation technique.
• Quality control procedures adopted for all sub-sampling stages to
maximise representivity of samples.
• Measures taken to ensure that the sampling is representative of the in
• Diamond Drilling - Core was cut down the structural long axis and the
same relative portion of half core was always sampled. Sample
intervals, true vein thickness, angle of vein to core axis and vein
composition were recorded.
For screen fire assays each core sample was submitted to the
laboratory, weighed, dried, and then pulverised in its entirety in an
LM2 to a P85 of -75 microns. For Leachwell digestion methods
sample protocol involved drill core samples of approximately 1kg
weighed, dried, crushed and pulverised in an LM2 (removable-bowl
Criteria
Quality of
assay data
and
laboratory
tests
JORC Code explanation
Commentary
situ material collected, including for instance results for field
duplicate/second-half sampling.
• Whether sample sizes are appropriate to the grain size of the material
being sampled.
pulveriser) to 85% passing -75 micron.
• Reverse Circulation Drilling - RC drilling: dust samples were collected
in a side-mounted cyclone and dumped into large plastic bags
annotated with the Hole Number and the interval depth. The bags
were stacked in order at each site. A wet sample was frequently
encountered at the water table. In all cases the water was able to be
controlled and only a few samples were damp in the entire program.
This is probably due to free draining old workings below the area of
RC drilling. After weighing on a floor scale, each sample was
carefully passed through a cradle riffle splitter by 2 field assistants
sufficient to produce a ~3kg sample for dispatch to the laboratory.
• Sample sizes are appropriate for the grain size of the material being
sampled.
• No systematic collection of field duplicate or second half sampling
was recorded.
• Prior to January 2007 all HEGL core samples were analysed by the
screen fire assay technique at the ALS Chemex Laboratory in
Orange, NSW. Each core sample was submitted to the laboratory,
weighed, dried, and then pulverised in its entirety in an LM2 to a P85
of -75 microns. The entire sample was weighed and wet screened
using -75 micron disposable nylon screen. The +75 micron fraction
was dried in aluminium trays, weighed and fire assayed to extinction.
The -75 micron fraction was collected using flocculant, the liquor then
decanted and the fines sample dried in an oven. This was
homogenised in the LM2, weighed and fire assayed in duplicate using
a 50 g charge. The assays for the -75 micron fraction were averaged
and a weighted average is calculated with the +75 micron fraction.
• In January 2007, drill core samples entered the production stream at
SGS Labs-Townsville and were assayed for gold by accelerated
cyanide leach using “Leachwell” reagent with fire assay finish.
Sample protocol involved drill core samples of approximately 1kg
weighed, dried, crushed and pulverised in an LM2 (removable-bowl
pulveriser) to 85% passing -75 micron followed by a quartz flush.
Both quartz flush and the sample were inserted in a Leachwell bottle
filled with water and a predetermined number of Leachwell tablets.
The containers were rolled for 24 hours whereupon the liquor was
• The nature, quality and appropriateness of the assaying and
laboratory procedures used and whether the technique is considered
partial or total.
• For geophysical tools, spectrometers, handheld XRF instruments, etc,
the parameters used in determining the analysis including instrument
make and model, reading times, calibrations factors applied and their
derivation, etc.
• Nature of quality control procedures adopted (eg standards, blanks,
duplicates, external laboratory checks) and whether acceptable levels
of accuracy (ie lack of bias) and precision have been established.
Criteria
JORC Code explanation
Commentary
•
•
•
•
•
homogenous and a subsample is extracted for fire assay. For
assays greater than 10g/t, bottle tails were washed filtered and fire
assayed. For assays greater than 50g/t, bottle tails were washed
filtered and screen fire assayed. This additional protocol ensured
coarse gold that may not have been dissolved in the accelerated
cyanide leach process was captured.
For HEGL, Reverse Circulation drilling produced 1 metre samples
which initially were all submitted for fire assay with any intervals
returning elevated gold being re-assayed by screen fire assay. PostDecember 2005, RC samples containing quartz were assayed by
screen fire assay. After January 2007 RC samples were assayed by
Leachwell methods.
Assay techniques are considered total and appropriate for the
mineralisation style.
There is no documentation of the systematic collection of field
duplicates or use of Certified Reference Material during the various
drilling and sampling programs to monitor the precision and accuracy
of the assay results. Instead, previous companies relied on the
quality control procedures of the laboratory undertaking the sample
assays to verify accuracy and precision.
Each sample assayed by screen fire assay method had a duplicate
50g firing from the -75 micron fraction.
The ALS Chemex QC protocol required that each batch of 50
samples analysed included a reagent blank, 3 replicate
determinations and 2 standard materials [Certified Reference
Material]. Samples exhibiting anomalous values (high or low) were
routinely analysed using either the original pulp or a second split. All
routine replicate analyses were reported to the client.
During the analytical sample preparation stage, crushing and grinding
equipment was flushed with barren quartz material between each
sample. The quartz flush sample was stored, which could later be
analysed to test for contamination or “loss of grade”.
Review of results of the lab’s internal QAQC results, indicate an
acceptable level of accuracy and precision has been established for
the drilling results.
Previous reporting on internal laboratory accuracy and precision has
Criteria
JORC Code explanation
Commentary
• The verification of significant intersections by either independent or
not raised any significant issues.
• The lack of QC at the sample collection stage is not considered to be
a significant problem with the data from the deposit, as reconciliation
of mined grades to model grades during trial production were within
acceptable tolerances for an area of Paxtons vein mined and
processed in 2008. Comparison of the estimated Mineral Resource
and mill production to the end of June 2009 revealed a gold content
reconciliation of 104%. .
• The drilling database was validated for overlapping sample intervals,
Verification
alternative company personnel.
compatibility of hole depths between database tables as well as collar
of sampling
• The use of twinned holes.
elevations compared to surface surveys and visual checks of drill hole
and
• Documentation of primary data, data entry procedures, data
traces in Surpac. No issues were found.
assaying
verification, data storage (physical and electronic) protocols.
•
Location of
data points
•
There are a number of drill holes that have intercepted mineralisation
Discuss any adjustment to assay data.
• Accuracy and quality of surveys used to locate drill holes (collar and
down-hole surveys), trenches, mine workings and other locations
used in Mineral Resource estimation.
• Specification of the grid system used.
• Quality and adequacy of topographic control.
•
•
•
•
•
•
within relatively close proximity to each other and these drill holes
have been investigated. Holes located less than 10m apart were
assessed and found to have satisfactory levels of similarity and
acceptable to be used in Resource estimation.
The majority of surface drill holes were surveyed using differential
GPS and underground holes surveyed by underground total station
methods.
Underground sample locations were located using a tape from the
nearest underground survey station which were generally less than
20m apart.
Holes paths were surveyed using a downhole gyro or an Eastman
single shot down-hole camera at 30 metres (or at the end of reverse
circulation pre-collars) and then every 50 metres to the end of holes.
The level of accuracy for drill hole locations is considered appropriate
for Resource estimation purposes.
This Resource estimate was undertaken using Zone 55 of the MGA94
grid coordinate system.
A reasonably detailed surface topographic survey was supplied. This
Resource estimate is not impacted by surface topography as the
uppermost extents of the mineralised domains occur between 60m
and 100m below the surface.
Criteria
Data spacing
and
distribution
JORC Code explanation
Commentary
• Data spacing for reporting of Exploration Results.
•
Drill hole intercept spacing averages around 10m to 40m along strike
• Whether the data spacing and distribution is sufficient to establish the
and around 10m to 20m in the dip direction. Underground drill fans
degree of geological and grade continuity appropriate for the Mineral
have resulted in intercepts as close as 2m apart in the dip direction.
Resource and Ore Reserve estimation procedure(s) and
classifications applied.
• Whether sample compositing has been applied.
•
• Whether the orientation of sampling achieves unbiased sampling of
•
•
Down hole sampling intervals vary from 10cm to 5.25m with an
average of 0.5m.
The data spacing and distribution is sufficient to establish grade
continuity appropriate for the Mineral Resource estimation
procedures and classifications applied.
No sample compositing was carried out prior to analysis.
Holes were drilled in an orientation to ensure sampling was
Orientation
possible structures and the extent to which this is known, considering
undertaken, as close as possible, orthogonal to the strike and dip of
of data in
the deposit type.
the mineralised vein packages. This orientation achieves the least
relation to
geological
structure
• If the relationship between the drilling orientation and the orientation
biased sample interval.
of key mineralised structures is considered to have introduced a
sampling bias, this should be assessed and reported if material.
• The measures taken to ensure sample security.
•
Sample
All samples were collected and sub-sampled on site by company
staff. Samples were submitted to the external laboratory using
security
• The results of any audits or reviews of sampling techniques and data.
•
Audits or
standard paperwork and delivered by company staff.
Review of QAQC data by Snowden (2006) showed moderate to high
variability in laboratory duplicate data, mainly in the lower grades
reviews
•
(<0.1g/t), but would not have a major impact on the global grade of
the resource.
HEG personnel undertook audits of the ALS laboratory in Orange
and the SGS laboratories in West Wyalong and Townsville with no
issues discovered that may have a negative impact on sample
preparation or analysis.
Section 2 Reporting of Exploration Results
(Criteria listed in the preceding section also apply to this section.)
Criteria
Mineral
tenement and
land tenure
status
Exploration
done by other
parties
Geology
Drill hole
Information
JORC Code explanation
Commentary
• Type, reference name/number, location and ownership including
agreements or material issues with third parties such as joint
ventures, partnerships, overriding royalties, native title interests,
historical sites, wilderness or national park and environmental
settings.
• The security of the tenure held at the time of reporting along with any
known impediments to obtaining a licence to operate in the area.
• The project is located within granted Exploration Licence EL5868
Mining leases ML1541, ML1116, ML315, ML316, ML317, ML49,
ML50, ML913, ML914, ML915 and GL5846 with the earliest expiry
date of 19 January 2033. The leases are held by Vertex Minerals Pty
Ltd.
• First Tiffany Resources Corporation is registered as having a 15%
interest in EL5868. (refer to Prospectus)
• The site is covered by EPL 12008, scheduled activity is mining for
minerals.
• Modern exploration of the Hill End goldfield has been carried out by
various companies since the early 1980’s using surface and
underground mapping and sampling, geophysical investigations,
diamond and reverse circulation drilling. Previous exploration
appears to have been performed to industry standards.
• Mineralisation at the Reward deposit occurs within a series of
bedding parallel quartz veins occurring along the limbs of the Hill End
Anticline which is located in the mid-Silurian to mid-Devonian Hill End
Trough containing sedimentary and volcanic rocks. The deposit is
best described as a brittle, thrust-dominated, competency-controlled
orogenic gold low sulphide system developed post ductile
deformation.
• There are approximately 3,800 separate drill holes and face sample
locations used in the estimate and tabulation of the information would
be cumbersome. A summary of all relevant drill hole and face sample
information in this report is considered not to be material to the
understanding of the report.
• Acknowledgment and appraisal of exploration by other parties.
• Deposit type, geological setting and style of mineralisation.
• A summary of all information material to the understanding of the
exploration results including a tabulation of the following information
for all Material drill holes:
o easting and northing of the drill hole collar
o elevation or RL (Reduced Level – elevation above sea level in
metres) of the drill hole collar
o dip and azimuth of the hole
o down hole length and interception depth
o hole length.
• If the exclusion of this information is justified on the basis that the
Criteria
Data
aggregation
methods
JORC Code explanation
•
•
•
Relationship
between
mineralisation
widths and
intercept
lengths
Diagrams
Balanced
reporting
Other
substantive
exploration
data
Further work
•
•
•
•
•
•
information is not Material and this exclusion does not detract from
the understanding of the report, the Competent Person should clearly
explain why this is the case.
In reporting Exploration Results, weighting averaging techniques,
maximum and/or minimum grade truncations (eg cutting of high
grades) and cut-off grades are usually Material and should be stated.
Where aggregate intercepts incorporate short lengths of high grade
results and longer lengths of low grade results, the procedure used
for such aggregation should be stated and some typical examples of
such aggregations should be shown in detail.
The assumptions used for any reporting of metal equivalent values
should be clearly stated.
These relationships are particularly important in the reporting of
Exploration Results.
If the geometry of the mineralisation with respect to the drill hole
angle is known, its nature should be reported.
If it is not known and only the down hole lengths are reported, there
should be a clear statement to this effect (eg ‘down hole length, true
width not known’).
Appropriate maps and sections (with scales) and tabulations of
intercepts should be included for any significant discovery being
reported These should include, but not be limited to a plan view of
drill hole collar locations and appropriate sectional views.
Where comprehensive reporting of all Exploration Results is not
practicable, representative reporting of both low and high grades
and/or widths should be practiced to avoid misleading reporting of
Exploration Results.
Other exploration data, if meaningful and material, should be reported
including (but not limited to): geological observations; geophysical
survey results; geochemical survey results; bulk samples – size and
method of treatment; metallurgical test results; bulk density,
groundwater, geotechnical and rock characteristics; potential
deleterious or contaminating substances.
• The nature and scale of planned further work (eg tests for lateral
extensions or depth extensions or large-scale step-out drilling).
Commentary
• Exploration results are not the subject of this report.
• Mineralised intercepts were composited to a nominal 1m in length for
the purpose of statistical analysis and grade estimation.
• No metal-equivalent values have been used in reporting (gold only).
• Exploration results are not the subject of this report.
• Holes were drilled to intersect the direction of main grade continuity at
approximate right angles.
• Maps and sections of the drill hole locations, mineralised intercepts
and domain interpretations are included in this report.
• Exploration results are not the subject of this report.
• All intersections have been included in the estimation of Mineral
Resources.
•
•
Exploration results are not the subject of this report.
Bulk density measurements and metallurgical test results are
discussed in the report.
•
There are no potentially deleterious elements in the Reward deposit.
• Further exploration work will include drilling to extend the Mineral
Resource along strike as well as up and down dip.
Criteria
JORC Code explanation
Commentary
• Diagrams clearly highlighting the areas of possible extensions,
including the main geological interpretations and future drilling areas,
provided this information is not commercially sensitive.
• A long section is included in the report showing the potential areas for
extension of the Resource (Exploration Target).
Section 3 Estimation and Reporting of Mineral Resources
(Criteria listed in section 1, and where relevant in section 2, also apply to this section.)
Criteria
Database
integrity
JORC Code explanation
Commentary
• Meas
Share your feedback
Discover